Outer Footprint
112.0 × 88.0 mm
R6.0 corners · 3.0 mm walls
Case Height
25.0 mm
Split @ 7.5 mm · 1.5 mm MX plate
3×3 Key Matrix
14.0 × 14.0 mm
19.05 mm 1U pitch · Handwired
2× EC11 Encoders
Ø7.2 mm · 29.0 mm
25.0 mm right of keys · Ø18 knobs
Rubber Feet (4×)
Ø10.5 × 1.0 mm
Recessed pockets (10 mm pads)
Foldable Legs (2×)
7.0° Tilt
Snap-in hinge · 95° open stop
Dimensioned Engineering Blueprints
Orthographic CAD views generated directly from the parametric model (all units in mm). Click any blueprint to inspect full-screen.
01 · TOP PLAN VIEW (MX PLATE & ENCODERS)
02 · BOTTOM UNDERSIDE (FEET, LEGS & M3 SCREWS)
03 · SIDE CROSS-SECTION, 7.0° DEPLOYED TILT & REAR MICRO-USB
Engineering Specifications & Clearances
| Overall Dimensions (Flat) | 112.0 × 88.0 × 25.0 mm (26.0 mm on 2 mm feet) |
|---|---|
| Wall / Plate / Floor | 3.0 mm walls · 1.5 mm MX top plate · 2.5 mm base floor |
| Case Split & Alignment | Split at Z = 7.5 mm with 2.0 mm interlocking step lip (0.25 mm clearance) |
| Switch Cutouts (9×) | 14.0 × 14.0 mm Cherry MX, 19.05 mm pitch, internal stiffening ribs |
| Rotary Encoders (2×) | Ø7.2 mm M7 panel holes at X = +31.55, Y = ±14.50 (29.0 mm pitch) |
| Case Fasteners (4×) | M3 screws at (±48.0, ±36.0) · Ø4.6 × 6.5 mm brass heat-set insert bosses |
| Rubber Feet Recesses (4×) | Ø10.5 × 1.0 mm deep at (±37.0, -35.0) & (±46.5, +24.5) |
| Foldable Legs (2×) | 14.0 × 10.0 × 4.0 mm snap-in arm, Ø2.6 mm chamfered pins in Ø3.0 mm sockets |
| Deployed Ergonomic Tilt | 7.0° toward user · 95° over-center positive stop · fingertip lift scoop |
| Raspberry Pi Pico 2W | 51.0 × 21.0 mm on 4× M2 standoffs (47.0 × 11.4 mm, H = 2.0 mm) |
| Internal Wiring Clearance | 5.9 mm clear above Pico 2W shield · 9.7 mm clear above Pico PCB to MX pins |
| Rear Micro-USB Opening | 12.5 × 8.0 mm rounded slot centered at X = 0, Z = 7.2 mm |
3D Printing Guide & Hardware BOM
Recommended FDM Print Settings (Zero Supports!)
- Top Case: Print top-face-down on the build plate. All 9 MX cutouts, 2 EC11 holes, and stiffening ribs print cleanly with zero supports.
- Bottom Case: Print bottom-face-down. The 1.0 mm rubber feet pockets, M3 counterbores, and leg pockets bridge cleanly at
0.20 mmlayer height. - Foldable Legs (×2): Print flat on build plate (side face down) so layer lines run lengthwise along the arm for maximum hinge pin strength.
- Material & Walls: PLA+ or PETG ·
0.20 mmlayers ·3–4perimeters ·20%gyroid infill.
Bill of Materials (BOM)
1×Raspberry Pi Pico 2W +4×M2×4 mm (or M2×5 mm) self-tapping screws9×Cherry MX-compatible mechanical switches + 1U keycaps + 1N4148 diodes2×EC11 panel-mount rotary encoders (M7 nut/washer) +2ר18 mm knobs4×M3×5.7 mm brass heat-set inserts +4×M3×8 mm (or M3×10 mm) SHCS4ר10 mm × 2 mm adhesive silicone rubber bumpon feet
Download CAD Files (STEP & STL)
Ready for slicing (STL) or further parametric editing in Fusion 360 / FreeCAD / SolidWorks (STEP).
STL
Top CasePrint top-face-down · 32.6 cm³
STL
Bottom CasePrint bottom-face-down · 31.5 cm³
STL
Foldable Leg (Print 2×)Snap-in hinge · 0.54 cm³ each
STEP
Full Case AssemblyAll 4 case solids (B-Rep)
STEP
Top Case (STEP)Editable solid B-Rep
STEP
Bottom Case (STEP)Editable solid B-Rep
STEP
Foldable Leg (STEP)Editable solid B-Rep