Outer Footprint
112.0 × 88.0 mm
R6.0 corners · 3.0 mm walls
Case Height
25.0 mm
Split @ 7.5 mm · 1.5 mm MX plate
3×3 Key Matrix
14.1 × 14.1 mm
19.05 mm 1U · FDM-tuned
2× EC11 Encoders
Ø7.3 mm · 29.0 mm
25.0 mm right of keys · Ø16–18 knobs
Rubber Feet (4×)
Ø10.5 × 1.0 mm
Recessed pockets (10 mm pads)
Foldable Legs (2×)
7.0° Tilt
Snap-in hinge · 95° open stop
Dimensioned Engineering Blueprints
Orthographic CAD views generated directly from the parametric model (all units in mm). Click any blueprint to inspect full-screen.
01 · TOP PLAN VIEW (MX PLATE & ENCODERS)
02 · BOTTOM UNDERSIDE (FEET, LEGS & M3 SCREWS)
03 · SIDE CROSS-SECTION, 7.0° DEPLOYED TILT & REAR MICRO-USB
Engineering Specifications & FDM Tolerance Audit
Every moving & mating interface includes explicit 3D-printing clearances and was boolean-verified to 0.00 mm³ interference—including a full 0° → 95° leg swing-arc sweep.
| Overall Dimensions (Flat) | 112.0 × 88.0 × 25.0 mm (3.0 mm walls · 1.5 mm plate · 2.5 mm floor) |
|---|---|
| Case Split & Seam Fit | Split at Z = 7.5 mm · 2.0 mm lip with 0.25 mm radial & 0.30 mm vertical clearance |
| Foldable Leg Swing Clearance | 0.40 mm per side (10.0 leg in 10.8 pocket) · 0.30 mm roof gap · 0.20 mm flush recess · 0°–95° sweep verified clear |
| Snap-In Hinge Pins | Ø2.6 mm chamfered pins in Ø3.0 mm sockets (0.20 mm radial clearance, 0.25 mm snap-in lip) |
| Switch Cutouts (9×) | 14.1 × 14.1 mm (+0.10 mm FDM shrinkage comp over 14.0 mm MX nominal), 19.05 mm pitch |
| Rotary Encoders (2×) | Ø7.3 mm holes (+0.30 mm over M7 bushing) at 29.0 mm vertical pitch (11–13 mm knob gap) |
| M3 Heat-Set Inserts (4×) | Ø4.0 × 6.5 mm pilot holes w/ 0.45 mm lead-in chamfer (exact fit for M3×5.7 mm OD 4.7 mm & M3×4 mm inserts) |
| M3 Screw Holes (4×) | Ø3.4 mm thru (+0.40 mm) · Ø6.2 × 3.5 mm counterbore · 0.20 mm clamping pull-down gap |
| Rubber Feet Pockets (4×) | Ø10.5 × 1.0 mm deep (+0.50 mm clearance for 10 mm pads; also fits 3M SJ5302 7.9 mm pads cleanly) |
| Pico 2W Mount & Wiring | 4× intact M2 standoffs (Ø1.8 mm pilot, 0.8 mm clear of rear wall & USB slot) · 5.9 mm above wireless shield |
| Rear Micro-USB Slot | 13.0 × 8.5 mm slot cutting strictly through the 3.0 mm rear wall (stops at Y = +40.9 mm, zero standoff contact) |
3D Printing Guide & Assembly Notes
Recommended FDM Print Settings (Zero Supports!)
- Top Case: Print top-face-down on the build plate. All 9 MX cutouts, 2 EC11 holes, and stiffening ribs print cleanly with zero supports.
- Bottom Case: Print bottom-face-down. Rubber feet pockets, M3 counterbores, and leg pockets bridge cleanly at
0.20 mmlayer height. - Foldable Legs (×2): Print flat on build plate (side face down) so layer lines run lengthwise along the arm for maximum hinge pin strength.
- Material & Walls: PLA+ or PETG (~65g total) ·
0.20 mmlayers ·3–4perimeters ·20%gyroid infill.
Quick Assembly Tips
- Heat-Set Inserts ("metal screw insets"): Set your soldering iron to ~210–225°C (PLA) or ~240°C (PETG), rest an M3 brass insert in the chamfered boss mouth, and press straight down gently until flush.
- Snap-In Legs: Align the leg's chamfered pins over the vertical lead-in ramps in each top-corner pocket and press firmly until they click into the
Ø3.0 mmpivot sockets. - Handwiring Matrix: Wire 3 rows (through 1N4148 diodes, cathode toward row) + 3 columns to 6 Pico GPIOs, plus 2× EC11 (A/B + push-button + GND) to 6 more GPIOs. Flash KMK (CircuitPython) or QMK!
Download CAD Files (STEP & STL)
Updated with all FDM tolerance refinements—ready for slicing (STL) or parametric editing (STEP).
STL
Top CasePrint top-face-down · 14.1mm MX · Ø4.0 inserts
STL
Bottom CasePrint bottom-face-down · 13×8.5mm USB
STL
Foldable Leg (Print 2×)Snap-in hinge · 0°–95° verified clear
STEP
Full Case AssemblyAll 4 case solids (B-Rep)
STEP
Top Case (STEP)Editable solid B-Rep
STEP
Bottom Case (STEP)Editable solid B-Rep
STEP
Foldable Leg (STEP)Editable solid B-Rep
Complete Budget Shopping List (One-Stop In-Stock Cart)
Every core part below is verified in stock on DigiKey.com and sold in exact quantities (no paying for 100-packs of switches, inserts, diodes, or feet)—around ~$39 total before flat-rate USPS shipping (~$6.99)!
DigiKey Core Cart: ~$39
Verified In Stock
1. Core Electronics, Clicky Switches & Case Hardware — All In Stock on DigiKey.com
| Item & Part # | Qty | Est. Price | Why You Need It / Fit Notes | Buy Link |
|---|---|---|---|---|
| Raspberry Pi Pico 2 W MPN: SC1633 |
1 |
$7.00 | Official RP2350 wireless board (un-soldered headers give maximum internal handwiring clearance). | DigiKey ↗ |
| Cherry MX2A Blue Clicky Switches (3-pin) MPN: MX2A-E1NN |
10(9 + 1 spare) |
~$9.00 (~$0.90 ea) |
Updated Cherry MX2A clicky plate-mount switches (factory-lubed, crisp click). Snaps snugly into our 14.1 mm FDM-tuned cutouts. |
DigiKey ↗ |
| Translucent White DSA 1U Keycaps (10-pack) DK: 1528-4956-ND |
1 pack(9 + 1 spare) |
$4.95 | Uniform DSA-profile MX keycaps (Adafruit #4956, in stock at DigiKey). | DigiKey ↗ |
| Bourns EC11 Rotary Encoder w/ Push Switch MPN: PEC11R-4215F-S0024 |
2 |
~$4.40 (~$2.20 ea) |
24-detent encoder w/ push-button, 15 mm flatted 6 mm D-shaft, and M7 threaded bushing (includes mounting nut & washer for Ø7.3 mm holes). |
DigiKey ↗ |
| Cliff 6 mm D-Shaft Control Knobs (Ø16.2 mm) DK: 4654-CL170852BR-ND |
2 |
$2.36 ($1.18 ea) |
Knurled black push-on knob with indicator line for 6 mm D-shafts. Fits our 29.0 mm encoder pitch with ~13 mm finger gap! |
DigiKey ↗ |
| 1N4148 Axial Signal Diodes (DO-35) DK: 1N4148FS-ND |
10(9 + 1 spare) |
$0.60 ($0.06 ea) |
1 diode per switch prevents key ghosting in the handwired 3×3 matrix (full N-key rollover). | DigiKey ↗ |
| 26 AWG Silicone Stranded Hookup Wire (25 ft) DK: 1528-1646-ND |
1 spool |
$4.95 | Flexible 200°C silicone-insulated wire (Adafruit #2514, in stock at DigiKey)—won't melt while soldering inside the case. | DigiKey ↗ |
| M3 × 5.7 mm Brass Heat-Set Inserts (OD 4.7 mm) DK: 2254-M30X226C-ND |
5(4 + 1 spare) |
$1.14 ($0.23 ea) |
Yes—these are the little brass metal screw insets! Exact standard Voron M3×5.7 mm spec; press 4 into the chamfered Ø4.0 × 6.5 mm top bosses with a soldering iron. |
DigiKey ↗ |
| 3M Bumpon Round Rubber Feet (Ø7.9 × 2.2 mm) MPN: SJ5302 |
5(4 + 1 spare) |
~$0.65 ($0.13 ea) |
Genuine 3M self-adhesive clear feet. Sits inside our Ø10.5 × 1.0 mm pockets with 1.2 mm protrusion (gives a crisp 6.8° deployed tilt). |
DigiKey ↗ |
| USB-A to Micro-B Data Cable (3 ft, Black) DK: 5214-UUSBHAUB3-ND |
1 |
~$3.50 | Shielded StarTech USB 2.0 data cable (skip if you already have a Micro-USB data cable). Plug boot fits our 13.0 × 8.5 mm rear slot. |
DigiKey ↗ |
2. The 8 Tiny Screws — Add to DigiKey Cart or Grab Locally (~$1–$2 at Ace / Home Depot)
| Screw Spec | Qty | Est. Price | Where They Go | Buy Link |
|---|---|---|---|---|
| M3 × 8 mm or M3 × 10 mm Machine Screws Socket Head Cap (DIN 912) or Pan Head |
4 screws |
~$1 local / ~$8 kit | Fastens bottom case into the 4× M3 brass heat-set inserts. Fits flush inside Ø6.2 × 3.5 mm bottom counterbores. |
|
| M2 × 4 mm or M2 × 5 mm Machine Screws DK: 5662-SETS-M2-4-ND (or local / Amazon) |
4 screws |
~$1 local / Included in kit | Mounts Raspberry Pi Pico 2W onto the 4× Ø1.8 mm self-tapping bottom standoffs (no nuts or heat-set inserts needed!). |
3. Peripheral Assembly Consumables & Basic Tools (Only Buy What You Don't Already Own)
Rosin-Core Solder (0.6–0.8 mm)
60/40 leaded or SAC305 lead-free for soldering switches, diodes, encoders & Pico pads
DigiKey ↗
Heat-Set Insert Tip (Optional)
A regular conical/chisel soldering tip at ~215°C works great for 4 inserts—just press straight down gently!
Amazon ↗
Bench Tools Checklist
Soldering iron · Wire strippers (26 AWG) · Flush cutters ·
Bench Basics
2.5 mm hex key (M3 SHCS) · PH0 / Torx driver (M2) · Tweezers · ~65g PLA+/PETG filament